#ifndef _DDS_H_ #define _DDS_H_ #include // Use pin 3 for PWM? If not defined, use pin 11 // Quality on pin 3 is higher than on 11, as it can be clocked faster // when the COMPARATOR_BITS value is less than 8 #define DDS_PWM_PIN_3 // Normally, we turn on timer2 and timer1, and have ADC sampling as our clock // Define this to only use Timer2, and not start the ADC clock // #define DDS_USE_ONLY_TIMER2 // Use a short (16 bit) accumulator. Phase accuracy is reduced, but speed // is increased, along with a reduction in memory use. #define SHORT_ACCUMULATOR #ifdef SHORT_ACCUMULATOR #define ACCUMULATOR_BITS 16 typedef uint16_t ddsAccumulator_t; #else #define ACCUMULATOR_BITS 32 typedef uint32_t ddsAccumulator_t; #endif // If defined, the timer will idle at 50% duty cycle // This leaves it floating in the centre of the PWM/DAC voltage range #define DDS_IDLE_HIGH // Select how fast the PWM is, at the expense of level accuracy. // A faster PWM rate will make for easier filtering of the output wave, // while a slower one will allow for more accurate voltage level outputs, // but will increase the filtering requirements on the output. // 8 = 62.5kHz PWM // 7 = 125kHz PWM // 6 = 250kHz PWM #ifdef DDS_PWM_PIN_3 #define COMPARATOR_BITS 6 #else // When using pin 11, we always want 8 bits #define COMPARATOR_BITS 8 #endif // This is how often we'll perform a phase advance, as well as ADC sampling // rate. The higher this value, the smoother the output wave will be, at the // expense of CPU time. It maxes out around 62000 (TBD) // May be overridden in the sketch to improve performance #ifndef DDS_REFCLK_DEFAULT #define DDS_REFCLK_DEFAULT 38400 #endif // As each Arduino crystal is a little different, this can be fine tuned to // provide more accurate frequencies. Adjustments in the range of hundreds // is a good start. #ifndef DDS_REFCLK_OFFSET #define DDS_REFCLK_OFFSET 0 #endif #ifdef DDS_USE_ONLY_TIMER2 // TODO: Figure out where this clock value is generated from #define DDS_REFCLK_DEFAULT (62500/4) #endif // Output some of the calculations and information about the DDS over serial #define DDS_DEBUG_SERIAL // When defined, use the 1024 element sine lookup table. This improves phase // accuracy, at the cost of more flash and CPU requirements. // #define DDS_TABLE_LARGE #ifdef DDS_TABLE_LARGE // How many bits to keep from the accumulator to look up in this table #define ACCUMULATOR_BIT_SHIFT (ACCUMULATOR_BITS-10) static const uint8_t ddsSineTable[1024] PROGMEM = { 128,128,129,130,131,131,132,133,134,135,135,136,137,138,138,139, 140,141,142,142,143,144,145,145,146,147,148,149,149,150,151,152, 152,153,154,155,155,156,157,158,158,159,160,161,162,162,163,164, 165,165,166,167,167,168,169,170,170,171,172,173,173,174,175,176, 176,177,178,178,179,180,181,181,182,183,183,184,185,186,186,187, 188,188,189,190,190,191,192,192,193,194,194,195,196,196,197,198, 198,199,200,200,201,202,202,203,203,204,205,205,206,207,207,208, 208,209,210,210,211,211,212,213,213,214,214,215,215,216,217,217, 218,218,219,219,220,220,221,221,222,222,223,224,224,225,225,226, 226,227,227,228,228,228,229,229,230,230,231,231,232,232,233,233, 234,234,234,235,235,236,236,236,237,237,238,238,238,239,239,240, 240,240,241,241,241,242,242,242,243,243,243,244,244,244,245,245, 245,246,246,246,246,247,247,247,248,248,248,248,249,249,249,249, 250,250,250,250,250,251,251,251,251,251,252,252,252,252,252,252, 253,253,253,253,253,253,253,254,254,254,254,254,254,254,254,254, 254,254,255,255,255,255,255,255,255,255,255,255,255,255,255,255, 255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,254, 254,254,254,254,254,254,254,254,254,254,253,253,253,253,253,253, 253,252,252,252,252,252,252,251,251,251,251,251,250,250,250,250, 250,249,249,249,249,248,248,248,248,247,247,247,246,246,246,246, 245,245,245,244,244,244,243,243,243,242,242,242,241,241,241,240, 240,240,239,239,238,238,238,237,237,236,236,236,235,235,234,234, 234,233,233,232,232,231,231,230,230,229,229,228,228,228,227,227, 226,226,225,225,224,224,223,222,222,221,221,220,220,219,219,218, 218,217,217,216,215,215,214,214,213,213,212,211,211,210,210,209, 208,208,207,207,206,205,205,204,203,203,202,202,201,200,200,199, 198,198,197,196,196,195,194,194,193,192,192,191,190,190,189,188, 188,187,186,186,185,184,183,183,182,181,181,180,179,178,178,177, 176,176,175,174,173,173,172,171,170,170,169,168,167,167,166,165, 165,164,163,162,162,161,160,159,158,158,157,156,155,155,154,153, 152,152,151,150,149,149,148,147,146,145,145,144,143,142,142,141, 140,139,138,138,137,136,135,135,134,133,132,131,131,130,129,128, 128,127,126,125,124,124,123,122,121,120,120,119,118,117,117,116, 115,114,113,113,112,111,110,110,109,108,107,106,106,105,104,103, 103,102,101,100,100,99,98,97,97,96,95,94,93,93,92,91, 90,90,89,88,88,87,86,85,85,84,83,82,82,81,80,79, 79,78,77,77,76,75,74,74,73,72,72,71,70,69,69,68, 67,67,66,65,65,64,63,63,62,61,61,60,59,59,58,57, 57,56,55,55,54,53,53,52,52,51,50,50,49,48,48,47, 47,46,45,45,44,44,43,42,42,41,41,40,40,39,38,38, 37,37,36,36,35,35,34,34,33,33,32,31,31,30,30,29, 29,28,28,27,27,27,26,26,25,25,24,24,23,23,22,22, 21,21,21,20,20,19,19,19,18,18,17,17,17,16,16,15, 15,15,14,14,14,13,13,13,12,12,12,11,11,11,10,10, 10,9,9,9,9,8,8,8,7,7,7,7,6,6,6,6, 5,5,5,5,5,4,4,4,4,4,3,3,3,3,3,3, 2,2,2,2,2,2,2,1,1,1,1,1,1,1,1,1, 1,1,0,0,0,0,0,0,0,0,0,0,0,0,0,0, 0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,1, 1,1,1,1,1,1,1,1,1,1,2,2,2,2,2,2, 2,3,3,3,3,3,3,4,4,4,4,4,5,5,5,5, 5,6,6,6,6,7,7,7,7,8,8,8,9,9,9,9, 10,10,10,11,11,11,12,12,12,13,13,13,14,14,14,15, 15,15,16,16,17,17,17,18,18,19,19,19,20,20,21,21, 21,22,22,23,23,24,24,25,25,26,26,27,27,27,28,28, 29,29,30,30,31,31,32,33,33,34,34,35,35,36,36,37, 37,38,38,39,40,40,41,41,42,42,43,44,44,45,45,46, 47,47,48,48,49,50,50,51,52,52,53,53,54,55,55,56, 57,57,58,59,59,60,61,61,62,63,63,64,65,65,66,67, 67,68,69,69,70,71,72,72,73,74,74,75,76,77,77,78, 79,79,80,81,82,82,83,84,85,85,86,87,88,88,89,90, 90,91,92,93,93,94,95,96,97,97,98,99,100,100,101,102, 103,103,104,105,106,106,107,108,109,110,110,111,112,113,113,114, 115,116,117,117,118,119,120,120,121,122,123,124,124,125,126,127 }; #else #define ACCUMULATOR_BIT_SHIFT (ACCUMULATOR_BITS-8) static const int8_t ddsSineTable[256] PROGMEM = { 0, 3, 6, 9, 12, 16, 19, 22, 25, 28, 31, 34, 37, 40, 43, 46, 49, 51, 54, 57, 60, 63, 65, 68, 71, 73, 76, 78, 81, 83, 85, 88, 90, 92, 94, 96, 98, 100, 102, 104, 106, 107, 109, 111, 112, 113, 115, 116, 117, 118, 120, 121, 122, 122, 123, 124, 125, 125, 126, 126, 126, 127, 127, 127, 127, 127, 127, 127, 126, 126, 126, 125, 125, 124, 123, 122, 122, 121, 120, 118, 117, 116, 115, 113, 112, 111, 109, 107, 106, 104, 102, 100, 98, 96, 94, 92, 90, 88, 85, 83, 81, 78, 76, 73, 71, 68, 65, 63, 60, 57, 54, 51, 49, 46, 43, 40, 37, 34, 31, 28, 25, 22, 19, 16, 12, 9, 6, 3, 0, -3, -6, -9, -12, -16, -19, -22, -25, -28, -31, -34, -37, -40, -43, -46, -49, -51, -54, -57, -60, -63, -65, -68, -71, -73, -76, -78, -81, -83, -85, -88, -90, -92, -94, -96, -98, -100, -102, -104, -106, -107, -109, -111, -112, -113, -115, -116, -117, -118, -120, -121, -122, -122, -123, -124, -125, -125, -126, -126, -126, -127, -127, -127, -127, -127, -127, -127, -126, -126, -126, -125, -125, -124, -123, -122, -122, -121, -120, -118, -117, -116, -115, -113, -112, -111, -109, -107, -106, -104, -102, -100, -98, -96, -94, -92, -90, -88, -85, -83, -81, -78, -76, -73, -71, -68, -65, -63, -60, -57, -54, -51, -49, -46, -43, -40, -37, -34, -31, -28, -25, -22, -19, -16, -12, -9, -6, -3 }; /*static const uint8_t ddsSineTable[256] PROGMEM = { 128,131,134,137,140,143,146,149,152,155,158,162,165,167,170,173, 176,179,182,185,188,190,193,196,198,201,203,206,208,211,213,215, 218,220,222,224,226,228,230,232,234,235,237,238,240,241,243,244, 245,246,248,249,250,250,251,252,253,253,254,254,254,255,255,255, 255,255,255,255,254,254,254,253,253,252,251,250,250,249,248,246, 245,244,243,241,240,238,237,235,234,232,230,228,226,224,222,220, 218,215,213,211,208,206,203,201,198,196,193,190,188,185,182,179, 176,173,170,167,165,162,158,155,152,149,146,143,140,137,134,131, 128,124,121,118,115,112,109,106,103,100,97,93,90,88,85,82, 79,76,73,70,67,65,62,59,57,54,52,49,47,44,42,40, 37,35,33,31,29,27,25,23,21,20,18,17,15,14,12,11, 10,9,7,6,5,5,4,3,2,2,1,1,1,0,0,0, 0,0,0,0,1,1,1,2,2,3,4,5,5,6,7,9, 10,11,12,14,15,17,18,20,21,23,25,27,29,31,33,35, 37,40,42,44,47,49,52,54,57,59,62,65,67,70,73,76, 79,82,85,88,90,93,97,100,103,106,109,112,115,118,121,124 };*/ #endif /* DDS_TABLE_LARGE */ class DDS { public: DDS(): refclk(DDS_REFCLK_DEFAULT), accumulator(0), running(false), timeLimited(false), tickDuration(0), amplitude(255) {}; // Start all of the timers needed void start(); // Is the DDS presently producing a tone? const bool isRunning() { return running; }; // Stop the DDS timers void stop(); // Start and stop the PWM output void on() { timeLimited = false; running = true; } // Provide a duration in ms for the tone void on(unsigned short duration) { // Duration in ticks from milliseconds is: // t = (1/refclk) tickDuration = (unsigned long)((unsigned long)duration * (unsigned long)refclk) / 1000; timeLimited = true; running = true; } void off() { running = false; } // Generate a tone for a specific amount of time void play(unsigned short freq, unsigned short duration) { setFrequency(freq); on(duration); } // Blocking version void playWait(unsigned short freq, unsigned short duration) { play(freq, duration); delay(duration); } // Use these to get some calculated values for specific frequencies // or to get the current frequency stepping rate. ddsAccumulator_t calcFrequency(unsigned short freq); ddsAccumulator_t getPhaseAdvance() { return stepRate; }; // Our maximum clock isn't very high, so our highest // frequency supported will fit in a short. void setFrequency(unsigned short freq) { stepRate = calcFrequency(freq); }; void setPrecalcFrequency(ddsAccumulator_t freq) { stepRate = freq; }; // Handle phase shifts void setPhaseDeg(int16_t degrees); void changePhaseDeg(int16_t degrees); // Adjustable reference clock. This shoud be done before the timers are // started, or they will need to be restarted. Frequencies will need to // be set again to use the new clock. void setReferenceClock(unsigned long ref) { refclk = ref; } unsigned long getReferenceClock() { return refclk; } uint8_t getDutyCycle(); // Set a scaling factor. To keep things quick, this is a power of 2 value. // Set it with 0 for lowest (which will be off), 8 is highest. void setAmplitude(unsigned char amp) { amplitude = amp; } // This is the function called by the ADC_vect ISR to produce the tones void clockTick(); private: volatile bool running; volatile unsigned long tickDuration; volatile bool timeLimited; volatile unsigned char amplitude; volatile ddsAccumulator_t accumulator; volatile ddsAccumulator_t stepRate; ddsAccumulator_t refclk; static DDS *sDDS; }; #endif /* _DDS_H_ */