Move not functioning examples to FixMe folder. Fix typos.

examples/AFSK_PacketTester/AFSK_PacketTester.ino

@@ -5,7 +5,7 @@
  * Connect the HamShield to your Arduino. Screw the antenna 
  * into the HamShield RF jack. Connect the Arduino to wall 
  * power and then to your computer via USB. After uploading 
- * this program to your adruino, open the Serial Monitor to 
+ * this program to your Arduino, open the Serial Monitor to 
  * monitor the process of the HamShield. Check for output on 
  * AFSK receiver.
 

examples/AFSK_SerialMessenger/AFSK_SerialMessenger.ino

@@ -4,7 +4,7 @@
  * seperate AFSK receiver to test the output of this example.
  * Connect the HamShield to your Arduino. Screw the antenna 
  * into the HamShield RF jack. After uploading this program 
- * to your adruino, open the Serial Monitor to monitor. Type 
+ * to your Arduino, open the Serial Monitor to monitor. Type 
  * a message under 254 characters into the bar at the top of 
  * the monitor. Click the "Send" button. Check for output on 
  * AFSK receiver.

examples/AX25Receive/AX25Receive.ino

@@ -6,7 +6,7 @@
  * into the HamShield RF jack. Plug a pair of headphones into 
  * the HamShield. Connect the Arduino to wall power and then to 
  * your computer via USB. After uploading this program to your 
- * adruino, open the Serial Monitor so you will see the AFSK 
+ * Arduino, open the Serial Monitor so you will see the AFSK 
  * packet. Send AFSK packet from AFSK equipment at 145.01MHz.
 
  *  Note: add message receive code

examples/CrystalCalibration/CrystalCalibration.ino

@@ -5,7 +5,7 @@
  * Connect the HamShield to your Arduino. Screw the antenna 
  * into the HamShield RF jack. Connect the Arduino to wall 
  * power and then to your computer via USB. After uploading 
- * this program to your adruino, open the Serial Monitor. 
+ * this program to your Arduino, open the Serial Monitor. 
  * Type 'h' into the bar at the top of the Serial Monitor 
  * and click the  "Send" button for more instructions.
 */

examples/FMBeacon/FMBeacon.ino

@@ -6,7 +6,7 @@
  * Connect the HamShield to your Arduino. Screw the antenna 
  * into the HamShield RF jack. Connect the Arduino to wall 
  * power and then to your computer via USB. After uploading 
- * this program to your adruino, open the Serial Monitor to 
+ * this program to your Arduino, open the Serial Monitor to 
  * monitor the status of the beacon. To test, set a HandyTalkie 
  * to 438MHz. You should hear the message " KC7IBT ARDUINO 
  * HAMSHIELD" in morse code.

examples/FixMe/HAMBot/HAMBot.ino

@@ -6,7 +6,7 @@
  * Connect the HamShield to your Arduino. Screw the antenna 
  * into the HamShield RF jack. Connect the Arduino to wall 
  * power and then to your computer via USB. After uploading 
- * this program to your adruino, you can send commands from 
+ * this program to your Arduino, you can send commands from 
  * your DTMF equipment using the following list: 
  * '4' => turn robot left
  * '6' => turn robot right

examples/FunctionalTest/FunctionalTest.ino

@@ -6,7 +6,7 @@
  * into the HamShield RF jack. Plug a pair of headphones into 
  * the HamShield. Connect the Arduino to wall power and then 
  * to your computer via USB. After uploading this program to 
- * your adruino, open the Serial Monitor. Serial Monitor will 
+ * your Arduino, open the Serial Monitor. Serial Monitor will 
  * describe what you should be expecting to hear from your 
  * headphones. Tune a HandytTalkie to 446MHz to hear morse 
  * code example.

examples/Gauges/Gauges.ino

@@ -6,7 +6,7 @@
  * into the HamShield RF jack. Plug a pair of headphones into 
  * the HamShield. Connect the Arduino to wall power and then 
  * to your computer via USB. After uploading this program to 
- * your adruino, open the Serial Monitor. You will see a 
+ * your Arduino, open the Serial Monitor. You will see a 
  * repeating display of different signal strengths. Ex: 
  *
  * [....|....] -73       

examples/HandyTalkie/HandyTalkie.ino

@@ -6,7 +6,7 @@
  * into the HamShield RF jack. Plug a pair of headphones into 
  * the HamShield. Connect the Arduino to wall power and then 
  * to your computer via USB. After uploading this program to 
- * your adruino, open the Serial Monitor. Press the button on 
+ * your Arduino, open the Serial Monitor. Press the button on 
  * the HamShield to begin setup. After setup is complete, type 
  * your desired Tx/Rx frequency, in hertz, into the bar at the 
  * top of the Serial Monitor and click the "Send" button. 

examples/JustTransmit/JustTransmit.ino

@@ -5,7 +5,7 @@
  * into the HamShield RF jack. Plug a pair of headphones with 
  * built-in mic into the HamShield. Connect the Arduino to 
  * wall power and then to your computer via USB. After 
- * uploading this program to your adruino, open the Serial 
+ * uploading this program to your Arduino, open the Serial 
  * Monitor to monitor the program's progress. After setup is 
  * complete, tune a HandyTalkie (HT) to 144.025MHz. Listen on 
  * the HT for the HamShield broadcasting from the mic.

examples/PSK31Transmit/PSK31Transmit.ino

@@ -5,7 +5,7 @@
  * Connect the HamShield to your Arduino. Screw the antenna 
  * into the HamShield RF jack. Connect the Arduino to wall 
  * power and then to your computer via USB. After uploading 
- * this program to your adruino, tune a PSK31 receiver and 
+ * this program to your Arduino, tune a PSK31 receiver and 
  * wait to receive the message "Why hello there, friend. 
  * Nice to meet you. Welcome to PSK31. 73, VE6SLP sk"
 */

examples/QPSK63Transmit/QPSK63Transmit.ino

@@ -5,7 +5,7 @@
  * Connect the HamShield to your Arduino. Screw the antenna 
  * into the HamShield RF jack. Connect the Arduino to wall 
  * power and then to your computer via USB. After uploading 
- * this program to your adruino, tune a QPSK63 receiver and 
+ * this program to your Arduino, tune a QPSK63 receiver and 
  * wait to receive the message "Why hello there, friend. 
  * Nice to meet you. Welcome to QPSK63. 73, VE6SLP sk"
 */

examples/SSTV/SSTV.ino

@@ -5,7 +5,7 @@
  * Connect the HamShield to your Arduino. Screw the antenna 
  * into the HamShield RF jack. Connect the Arduino to wall 
  * power and then to your computer via USB. After uploading 
- * this program to your adruino, open the Serial Monitor to 
+ * this program to your Arduino, open the Serial Monitor to 
  * view the status of the program. Tune your SSTV to 
  * 446MHz to receive the image output.
 */

examples/SSTV_M1_Static/SSTV_M1_Static.ino

@@ -5,7 +5,7 @@
  * Connect the HamShield to your Arduino. Screw the antenna 
  * into the HamShield RF jack. Connect the Arduino to wall 
  * power and then to your computer via USB. After uploading 
- * this program to your adruino, open the Serial Monitor to 
+ * this program to your Arduino, open the Serial Monitor to 
  * view the status of the program. Tune your SSTV to 
  * 145.5MHz to receive the image output.
 */

examples/SerialTransceiver/SerialTransceiver.ino

@@ -6,7 +6,7 @@
  * into the HamShield RF jack. Plug a pair of headphones into 
  * the HamShield. Connect the Arduino to wall power and then 
  * to your computer via USB. After uploading this program to 
- * your adruino, open the Serial Monitor. Use the bar at the 
+ * your Arduino, open the Serial Monitor. Use the bar at the 
  * top of the serial monitor to enter commands as seen below.
  * 
  * EXAMPLE: To change the repeater offset to 144.425MHz, 

examples/SignalTest/SignalTest.ino

@@ -9,7 +9,7 @@
  * into the HamShield RF jack. Plug a pair of headphones into 
  * the HamShield. Connect the Arduino to wall power and then 
  * to your computer via USB. After uploading this program to 
- * your adruino, open the Serial Monitor. HamShield will print 
+ * your Arduino, open the Serial Monitor. HamShield will print 
  * the results of its signal test to the Serial Monitor. To 
  * test with another HandyTalkie (HT), tune in to 446MHz and 
  * listen for the call sign. Then key up on your HT and make