212 lines
9.0 KiB
C++
212 lines
9.0 KiB
C++
/*
|
|
|
|
SerialTransceiver is TTL Serial port "glue" to allow desktop or laptop control of the HAMShield
|
|
|
|
Commands:
|
|
|
|
Mode ASCII Description Implemented
|
|
-------------- ----------- -------------------------------------------------------------------------------------------------------------------------------------------- -----------------
|
|
Transmit space Space must be received at least every 500 mS Yes
|
|
Receive not space If space is not received and/or 500 mS timeout of space occurs, unit will go into receive mode Yes
|
|
CTCSS In A<tone>; <tone> must be a numerical ascii value with decimal point indicating CTCSS receive tone required to unsquelch No
|
|
CTCSS Out B<tone>; <tone> must be a numerical ascii value with decimal point indicating CTCSS transmit tone No
|
|
CTCSS Enable C<state>; Turns on CTCSS mode (analog tone) with 1, off with 0. No
|
|
CDCSS Enable D<state>; Turns on CDCSS mode (digital tone) with 1, off with 0. No
|
|
Bandwidth E<mode>; for 12.5KHz mode is 0, for 25KHz, mode is 1 No
|
|
Frequency F<freq>; Set the receive frequency in KHz, if offset is disabled, this is the transmit frequency No
|
|
CDCSS In G<code>; <code> must be a valid CDCSS code No
|
|
CDCSS Out H<code>; <code> must be a valid CDCSS code No
|
|
Print tones I Prints out all configured tones and codes, coma delimited in format: CTCSS In, CTCSS Out, CDCSS In, CDCSS Out No
|
|
Morse Out M<text>; A small buffer for morse code (32 chars)
|
|
Power level P<level>; Set the power amp level, 0 = lowest, 15 = highest No
|
|
Enable Offset R<state>; 1 turns on repeater offset mode, 0 turns off repeater offset mode No
|
|
Squelch S<level>; Set the squelch level No
|
|
TX Offset T<freq>; The absolute frequency of the repeater offset to transmit on in KHz No
|
|
Volume V<level>; Set the volume level of the receiver No
|
|
Reset X Reset all settings to default No
|
|
Sleep Z Sleep radio No
|
|
Filters @<state>; Set bit to enable, clear bit to disable: 0 = pre/de-emphasis, 1 = high pass filter, 2 = low pass filter (default: ascii 7, all enabled) No
|
|
Vox mode $<state>; 0 = vox off, >= 1 audio sensitivity. lower value more sensitive No
|
|
Mic Channel *<state>; Set the voice channel. 0 = signal from mic or arduino, 1 = internal tone generator No
|
|
RSSI ? Respond with the current receive level in - dBm (no sign provided on numerical response) No
|
|
Tone Gen % (notes) To send a tone, use the following format: Single tone: %1,<freq>,<length>; Dual tone: %2,<freq>,<freq>,<length>; DTMF: %3,<key>,<length>; No
|
|
Voice Level ^ Respond with the current voice level (VSSI)
|
|
|
|
|
|
Responses:
|
|
|
|
Condition ASCII Description
|
|
------------ ---------- -----------------------------------------------------------------
|
|
Startup *<code>; Startup and shield connection status
|
|
Success !; Generic success message for command that returns no value
|
|
Error X<code>; Indicates an error code. The numerical value is the type of error
|
|
Value :<value>; In response to a query
|
|
Status #<value>; Unsolicited status message
|
|
Debug Msg @<text>; 32 character debug message
|
|
|
|
*/
|
|
|
|
#include "Wire.h"
|
|
#include "HamShield.h"
|
|
|
|
int state;
|
|
int txcount = 0;
|
|
long timer = 0;
|
|
long freq = 144390;
|
|
long tx = 0;
|
|
char cmdbuff[32] = "";
|
|
int temp = 0;
|
|
int repeater = 0;
|
|
float ctcssin = 0;
|
|
float ctcssout = 0;
|
|
int cdcssin = 0;
|
|
int cdcssout = 0;
|
|
|
|
|
|
HamShield radio;
|
|
|
|
|
|
|
|
void setup() {
|
|
Serial.begin(115200);
|
|
Serial.print(";;;;;;;;;;;;;;;;;;;;;;;;;;");
|
|
Wire.begin();
|
|
int result = radio.testConnection();
|
|
Serial.print("*");
|
|
Serial.print(result,DEC);
|
|
Serial.print(";");
|
|
radio.initialize(); // initializes automatically for UHF 12.5kHz channel
|
|
Serial.print("*START;");
|
|
radio.frequency(freq);
|
|
radio.setVolume1(0xF);
|
|
radio.setVolume2(0xF);
|
|
radio.setModeReceive();
|
|
radio.setTxSourceMic();
|
|
radio.setRfPower(9);
|
|
radio.setSQLoThresh(80);
|
|
radio.setSQOn();
|
|
}
|
|
|
|
void loop() {
|
|
|
|
if(Serial.available()) {
|
|
|
|
int text = Serial.read();
|
|
|
|
switch (state) {
|
|
|
|
case 10:
|
|
if(text == 32) { timer = millis();}
|
|
break;
|
|
|
|
case 0:
|
|
switch(text) {
|
|
|
|
case 32: // space - transmit
|
|
if(repeater == 1) { radio.frequency(tx); }
|
|
radio.setModeTransmit();
|
|
state = 10;
|
|
Serial.print("#TX,ON;");
|
|
timer = millis();
|
|
break;
|
|
|
|
case 63: // ? - RSSI
|
|
Serial.print(":");
|
|
Serial.print(radio.readRSSI(),DEC);
|
|
Serial.print(";");
|
|
break;
|
|
|
|
case 65: // A - CTCSS In
|
|
getValue();
|
|
ctcssin = atof(cmdbuff);
|
|
radio.setCtcss(ctcssin);
|
|
break;
|
|
|
|
case 66: // B - CTCSS Out
|
|
break;
|
|
|
|
case 67: // C - CTCSS Enable
|
|
break;
|
|
|
|
case 68: // D - CDCSS Enable
|
|
break;
|
|
|
|
case 70: // F - frequency
|
|
getValue();
|
|
freq = atol(cmdbuff);
|
|
if(radio.frequency(freq) == true) { Serial.print("@"); Serial.print(freq,DEC); Serial.print(";!;"); } else { Serial.print("X1;"); }
|
|
break;
|
|
|
|
case 'M':
|
|
getValue();
|
|
radio.setModeTransmit();
|
|
delay(300);
|
|
radio.morseOut(cmdbuff);
|
|
state = 10;
|
|
break;
|
|
|
|
case 80: // P - power level
|
|
getValue();
|
|
temp = atol(cmdbuff);
|
|
radio.setRfPower(temp);
|
|
break;
|
|
|
|
case 82: // R - repeater offset mode
|
|
getValue();
|
|
temp = atol(cmdbuff);
|
|
if(temp == 0) { repeater = 0; }
|
|
if(temp == 1) { repeater = 1; }
|
|
break;
|
|
|
|
case 83: // S - squelch
|
|
getValue();
|
|
temp = atol(cmdbuff);
|
|
radio.setSQLoThresh(temp);
|
|
break;
|
|
|
|
case 84: // T - transmit offset
|
|
getValue();
|
|
tx = atol(cmdbuff);
|
|
break;
|
|
|
|
|
|
case 94: // ^ - VSSI (voice) level
|
|
Serial.print(":");
|
|
Serial.print(radio.readVSSI(),DEC);
|
|
Serial.print(";");
|
|
}
|
|
break;
|
|
}
|
|
|
|
}
|
|
if(state == 10) {
|
|
if(millis() > (timer + 500)) { Serial.print("#TX,OFF;");radio.setModeReceive(); if(repeater == 1) { radio.frequency(freq); } state = 0; txcount = 0; }
|
|
}
|
|
}
|
|
|
|
void getValue() {
|
|
int p = 0;
|
|
char temp;
|
|
for(;;) {
|
|
if(Serial.available()) {
|
|
temp = Serial.read();
|
|
if(temp == 59) { cmdbuff[p] = 0; Serial.print("@");
|
|
for(int x = 0; x < 32; x++) { Serial.print(cmdbuff[x]); }
|
|
return;
|
|
}
|
|
cmdbuff[p] = temp;
|
|
p++;
|
|
if(p == 32) {
|
|
Serial.print("@");
|
|
for(int x = 0; x < 32; x++) {
|
|
Serial.print(cmdbuff[x]);
|
|
}
|
|
|
|
cmdbuff[0] = 0;
|
|
|
|
Serial.print("X0;"); return; } // some sort of alignment issue? lets not feed junk into whatever takes this string in
|
|
}
|
|
}
|
|
}
|
|
|