boxmaker/docs/runbook.md

Runbook

One entry for every state in which Boxmaker refuses to work or holds something back, and for events worth understanding when you see them. Every message for such a state ends with see docs/runbook.md#<entry>; a gate check makes sure the entry exists.

Each entry says what you see, why the system refuses, how to confirm, how to fix, and how to check the fix. Commands assume:

• $BOXMAKER_HOME is the harness home: /var/lib/boxmaker when deployed, .state in the repository during development.
• $GRANTS is [paths] grants from brokerd.toml: /etc/boxmaker/grants when deployed.
• Until M7 there are no service units: the daemons run in a terminal, and "stop" means Ctrl-C or pkill -x <name>.

Entries for M3a states are written ahead of the code and describe it as specified in docs/specs/2026-09-18-m3a-decision-path.md.

grants-invalid

What you see. brokerd prints one or more lines naming a grant file and a problem, then this entry. Every tool call is denied, and the model tells you "the grant files have an error".

Why. One grant file is invalid, so brokerd denies everything until it is fixed. It cannot skip the bad file: if the bad file was a deny grant, skipping it would allow what it was written to forbid.

Confirm.

bxctl grants check

It prints each problem as <file>:<line>: <problem>. Common ones: a misspelled field (unknown fields are errors); secret set (not supported until M4); patterns set (not supported); hosts on a file tool or paths on http_fetch; a relative path or one with .., . or //; a host with uppercase letters, a port, or an IP address; a file name with characters outside [a-z0-9-].

Fix. Edit the file, or move it out of $GRANTS while you work on it:

mkdir -p ~/grants-parked && mv "$GRANTS/<file>.toml" ~/grants-parked/

Do not park a deny grant unless you are sure nothing else would then allow what it forbids.

Check. bxctl grants check prints grants: ok. No restart is needed: brokerd reads the grants again at the next call.

audit-unavailable

What you see. brokerd prints an error writing to $BOXMAKER_HOME/audit/, then this entry. Tool calls are denied, and the model says "the audit log cannot be written".

Why. A call runs only after its decision is on disk. If the record cannot be written, nothing runs.

Confirm.

df -h "$BOXMAKER_HOME"
ls -ld "$BOXMAKER_HOME/audit"; ls -l "$BOXMAKER_HOME/audit" | tail -3

Look for a full disk, a directory or file not owned by the user brokerd runs as, or a read-only file system.

Fix. Free space or correct ownership (chown to the brokerd user; files are mode 0600, the directory 0700). Do not edit, move or delete audit files to make space: that breaks the chain.

Check. Ask for any tool call. It is decided normally, and bxctl audit verify prints audit: ok. If brokerd keeps failing after the cause is gone, stop and start it.

audit-chain-broken

What you see. brokerd refuses to start and prints <file>:<line>: <what>, then this entry. Or bxctl audit verify prints the same and exits 1.

Why. A record does not parse, its seq is not the next number, its prev is not the hash of the line before, or a file does not continue from the one before it. Something changed the log after it was written: an edit, a deleted or reordered line, a file restored from a backup, a partial copy. brokerd will not add records after a history it cannot vouch for.

Confirm.

bxctl audit verify
sed -n '<line-1>,<line+1>p' "$BOXMAKER_HOME/audit/<file>"

Work out what happened before going on: a restore, a manual edit, a disk problem, or none you know of. If none you know of, treat it as a possible intrusion and keep the files as they are.

Fix. Keep a copy first, then accept the break explicitly:

cp -a "$BOXMAKER_HOME/audit" ~/audit-copy-$(date +%F)
brokerd serve --config <path> --accept-break

brokerd appends an accepted_break record naming the file and line, and continues from there. Nothing is repaired or deleted. The break stays visible in every later verification.

Check. bxctl audit verify prints audit: ok and lists the accepted break with its file and line. A second failure later in the log needs its own accepted break.

audit-recovered

What you see. brokerd prints "audit: recovered a torn final line" at start, then this entry. It starts normally.

Why. The last record was being written when brokerd or the machine stopped, so the file ended without a newline. That is expected after a crash, not an error. brokerd kept the partial line, ended it, and wrote a recovery record holding its length and hash, chained from the last complete record. The partial record was never acted on: records are written before the action they allow.

Confirm. bxctl audit verify lists the recovery with its file and line.

Fix. None needed. If recoveries happen often, find out why brokerd is being killed.

Check. bxctl audit verify prints audit: ok.

brokerd-already-running

What you see. brokerd exits at start with "brokerd is already running" and this entry.

Why. Only one brokerd may write the audit log. It holds a lock on $BOXMAKER_HOME/audit/.lock for as long as it runs, and the lock is released when the process ends, however it ends.

Confirm.

pgrep -a brokerd

Fix. Use the running one, or stop it (pkill -x brokerd) and start again. Deleting .lock does not help and is not needed.

Check. pgrep -a brokerd shows one process.

broker-state-damaged

What you see. brokerd prints an error reading or writing $BOXMAKER_HOME/broker/sessions/<id>.json, then this entry. Either every call for that session is denied ("this session's broker state is damaged"), or one call failed with "the result could not be recorded".

Why. The file holds the session's taint and untrusted flag. If brokerd cannot read it, it does not know how sensitive the session's data is, so it denies. If it cannot write it after a tool ran, it withholds the result: content that raised the taint must not reach the model unless the raised taint is on disk.

Confirm.

ls -l "$BOXMAKER_HOME/broker/sessions/<id>.json"*
cat "$BOXMAKER_HOME/broker/sessions/<id>.json"
df -h "$BOXMAKER_HOME"

A good file is one line such as {"taint":"private","untrusted":false}.

Fix. For a write failure, fix space or ownership as in audit-unavailable. For a damaged file, do not guess low: set it from the session's results. The session's audit result records show the highest taint_after, and any result from an untrusted grant means "untrusted":true. If unsure, write {"taint":"secret","untrusted":true}, which is always safe. The session only loses access to grants with a lower max_taint. A .tmp file beside it is a write that did not finish and can be removed.

Check. The next call for the session is decided normally.

socket-forbidden

What you see. brokerd prints that a message of some kind arrived on the wrong socket, then this entry.

Why. broker.sock accepts only tool requests from loopd; admin.sock accepts only admin requests from bxctl. Nothing in the harness sends a wrong kind, so this is a bug or a component doing what it should not, such as something trying to approve through the tool socket.

Confirm. Note the time, kind and socket. Check what was running: pgrep -a 'loopd|bxctl'. Look at the session logs active at that time.

Fix. If a harness version mismatch explains it (a new bxctl against an old brokerd), rebuild and restart both. Otherwise keep the logs, stop loopd, and investigate before running it again.

Check. No further messages of this kind.

broker-unavailable

What you see. loopd prints that it cannot reach broker.sock, then this entry. Tool calls fail with "the tool broker is unavailable", the model says so, and the conversation goes on.

Why. brokerd is not running, was restarted during a call, or loopd's [broker] socket points somewhere else. Pending approvals are lost when brokerd restarts. bxctl audit verify lists them as abandoned.

Confirm.

pgrep -a brokerd
ls -l "$BOXMAKER_HOME/run/loop-broker/"

Compare the socket path with [broker] socket in loopd's config and [sockets] broker in brokerd.toml.

Fix. Start brokerd, or make the two paths agree. loopd needs no restart: it connects per call.

Check. Ask the model to use a tool. The call is decided (allowed, asked or denied) instead of failing.

loopd-selftest-failed

What you see. loopd prints selftest: FAILED: <reason> and this entry, and exits 1.

Why. loopd will not start against a server that differs from the one its config describes, that does not parse tool calls, or whose cache does not work.

Confirm and fix, by reason.

• chat template sha256: expected …, got …, context per slot: … or slot count: …. The server changed: a model update, or new flags in ~/src/nixos/hw/straylight/default.nix. Check what changed on straylight. If the change is intended, update [expect] in loopd's config:

  curl -s 'http://straylight:11434/props?model=ornith-1.5-35b-a3b' | jq -j .chat_template | sha256sum
  curl -s 'http://straylight:11434/props?model=ornith-1.5-35b-a3b' | jq '.default_generation_settings.n_ctx, .total_slots'
  

  A template change also invalidates the M0 measurements. Re-run the checks in docs/inference-contract.md before trusting the cache behaviour.

• the tool call did not come back parsed: …. The template or the server's tool parser changed. Treat it like a template change. Do not start loopd until tool calls parse again.

• turn 2 did not reuse turn 1's cache: …. Another client may have taken the slot between the two requests. Check curl -s 'http://straylight:11434/slots?model=ornith-1.5-35b-a3b' and run loopd selftest --config <path> again. If it fails twice with the slot otherwise idle, the cache is not working: check the server flags for cache_prompt and the KV settings.

• A connection, timeout or HTTP error. Check that inferproxy is running and that its upstream answers: curl -s http://straylight:11434/health. A model load can take tens of seconds, so retry once.

Check. loopd selftest --config <path> prints selftest: ok.

session-log-damaged

What you see. A turn on an existing session fails with <file>:<line>: <reason> naming sessions/<id>/<epoch>.jsonl, and this entry. Other sessions work.

Why. loopd replays the log exactly to rebuild the conversation, so a line it cannot read would change what the model sees. It refuses rather than guess. last line does not end in a newline means a write was cut off: loopd writes a record only after the request it describes has finished, so a cut-off line was never used.

Confirm.

f="$BOXMAKER_HOME/sessions/<id>/0.jsonl"
wc -l "$f"; tail -c 300 "$f"

Fix. Keep a copy first. Then either start a new session (always safe), or, for a cut-off last line only, drop it:

cp -a "$f" "$f.damaged-$(date +%s)"
head -n <line-1> "$f.damaged-"* > "$f"      # keep the complete lines before the damaged one

Anything else (a damaged line in the middle, an unknown record type) means the file was changed by something other than loopd. Start a new session and keep the old log for inspection.

Check. The next turn on the session succeeds. The first request re-reads the conversation if the cache was lost, which loopd logs as a cache loss.

core-memory-unreadable

What you see. Starting a new session fails with an error naming memory/core.md, and this entry. Existing sessions still work: they use the baseline saved when they started.

Why. memory/core.md exists but cannot be read. A missing file is fine, but starting without memory you wrote, and without telling you, is not.

Confirm.

ls -l "$BOXMAKER_HOME/memory/core.md"; head -c 100 "$BOXMAKER_HOME/memory/core.md"

Look for wrong ownership or mode, or a file that is not UTF-8 text.

Fix. Make it readable by the user loopd runs as (chmod 0600 and chown to that user), or save it again as UTF-8.

Check. A new session starts, and its 0.baseline.json contains the text.